Better understanding of structural strengthening

To the beginner

1. The reinforcement method of changing the structural layout and load transfer way is called ( ).

A. direct reinforcement method

B. changing load transfer reinforcement method

C. jacket structure reinforcement method

D. enlargement section method


Correct answer: B


2. In the following options, () is not a reinforcement method for concrete columns.

A. enlargement section method

B. replacement method

C. prestress method

D. internal clad steel method


Correct answer: C


3. ( ) is the most commonly used wall reinforcement method in engineering.

A. enlargement section method

B. outsourced angle steel method

C. buttress column method

D. Adding rebar net surface layer 


Correct answer: C


4. The design value of the tensile strength of the new longitudinal reinforcement should be multiplied by ( ) of the strength utilization coefficient when the loading capacity of the normal section is checked for the condition that the tensile zone is thickened and reinforced.

A. 0.85

B. 0.90

C. 0.95

D. 0.80


Correct answer: B


5. When the number of wall cracks is small and the number of cracking walls is large, it can be used ( ).

A. grouting reinforcement method

B. dismantling prestress plate

C. non prestressed slab

D. prefabricated hollow plate


Correct answer: A


6.The most effective measure to improve flexural rigidity (reduce disturbance) of reinforced concrete flexural members is ().

A. improves the strength grade of concrete

B. increases the section area of the drawn steel bar

C. increases the effective height of the cross section

D. enlarging the width of the section


Correct answer: C


7.The following ( ) is not a variable load.

A.Self weight of structural members

B. house area ash

C. wind load

D. crane load


Correct answer: A


8.The procedures and principles that should be followed in the construction of reinforced concrete structures.

A. clean up the defects of original concrete components to dense parts.

B. chisel the surface of the original component or make it into a trench

C. the concrete edges and corners of the bags should be destroyed and the floating debris and dust should be removed.

D. the original concrete surface should be washed clean. Before pouring concrete, the raw concrete surface should be treated with fresh cement paste or other interface agents.


Correct answer: ABCD


9.The method of strengthening concrete columns by enlarging section method is ().

A. outsourcing

B. one side thickening

C. thickening both sides

D. three surface thickening


Correct answer: ABC


10.If it is a super reinforced beam, the reinforcement method should be adopted.

A. method of increasing cross section

B. method of adopting additional fulcrum

C. reinforcing bar in drawing area

D. configuration stirrup


Correct answer: AB


11.The reinforcement of beams and plates due to insufficient bearing capacity includes two aspects.

A. cross section reinforcement

B. oblique section reinforcement

C. bending failure reinforcement

D. reinforcement and failure of bending


Correct answer: AB


12. Additional reinforcement reinforcement method, which is more suitable for what kind of situation.

A.The section size of the beam can meet the requirement of stiffness

B.The shear bearing capacity of the beam also meets the requirements

C.The flexural tensile strength of the beam can not meet the requirements

D.The amount of reinforcement of the tensile reinforcement of the beam is not very large


Correct answer: ABCD


13.The principle of building structure reinforcement design is.

A .reinforcement of components and reinforcement of structural system

B. local reinforcement and overall reinforcement

C. temporary reinforcement and permanent reinforcement

D. high cost reinforcement and low cost reinforcement


Correct answer: ABC


14.The appearance of concrete beams and plates is insufficient.

A. The deflection of the component is larger

B. The crack is too wide and too long

C. Serious corrosion of steel bar

D. Concrete has signs of crushing in the compressed area


Correct answer: ABCD




  


Horse Construction Recommended Products

You can find anything here you are in need of, have a trust trying on these products, you will find the big difference after that.

HM-20 Unidirectional Carbon Fiber Wrap

High strength, unidirectional carbon fiber wrap pre-saturated to form a carbon fiber reinforced polymer (CFRP) wrap used to strengthen structural concrete elements.

See more >

HM-1.2T Unidirectional Carbon Fiber Strip

High strength carbon fiber reinforced polymer (CFRP) strip / laminate / plate for structural strengthening and concrete repair

See more >

HM-MJ50/100 Prestressed CFRP Plate System

Prestressed carbon fiber reinforced polymer(CFRP) plate for slab, beam strengthening to increase stiffness, reduce distortion and deflection of members, reduce the cracks, avoid and stop cracking.

See more >

Back
Top
Close